<delect id="db3ph"></delect>
    <track id="db3ph"></track>

    <cite id="db3ph"></cite>

    <big id="db3ph"></big>

    <th id="db3ph"><meter id="db3ph"><span id="db3ph"></span></meter></th><track id="db3ph"></track>

      <rp id="db3ph"><span id="db3ph"><th id="db3ph"></th></span></rp><address id="db3ph"></address>

        <big id="db3ph"></big>
        Alconox,Liqui-nox,Citranox,Alcojet,Citrajet,Detergent 8,Det-O-Jet,Terg-A-Zyme,Luminox,ALCOTABS等系列清洗劑可以用于醫療清洗,制藥廠設備清洗,食品工廠設備清洗,電子及半導體清洗,光學清洗!
        首  頁 | 公司簡介 | 主要產品 | 新聞中心 | 技術應用 | 聯系我們
        PCBA Cleaning線路板組裝件清洗,Misprint Cleaning誤印版清洗,Stencil Cleaning印刷鋼網清洗
        Detergent 8低泡沫無磷清洗劑








        I assume you are speaking of cleaning PCBs with a brush and a small bottle of alcohol, or sometimes in an open top cleaning machine of some sort. In that case, you will find there are at three main problems with alcohol:

        First, alcohol is "hygroscopic." This means it absorbs water from the air, which dilutes the alcohol and weakens its ability to clean. Alcohol also is often diluted commercially by 20% or more, to keep the price down.

        This dramatically reduces its cleaning strength. Using weak, water-filled alcohol is a bad process that can lead to labor-intensive cleaning. Make sure you specify the purest, most water-free alcohol you can find.

        Secondly, alcohol is a very weak cleaner. It has a low Kb value and it saturates with flux residues at 2% by weight. So it takes a lot of solvent to successfully clean a typical circuit board. It's not the cost of the solvent that is the issue -- it's the cost of time lost cleaning inefficiently. So here are some steps you can take that will help cleaning work better:

        Use clean bottles and clean brushes, and make sure your techs clean both items daily.
        Make the techs clean with the board held at an angle, so the excess solvent runs off the board and doesn't stay and redeposit the contamination. If the solvent stays on the board, you're going to have dirty boards no matter how much the techs scrub.
        Provide the techs with clean, lint-free wipes to absorb alcohol and flux residues. Make sure they use them, and dispose of them, rather than re-using them.
        Consider upgrading to a more powerful solvent, a more sophisticated dispensing system and/or even an automated cleaner for faster, more reliable cleaning.
        Special Note: In Circuits Assembly Magazine in Dec. 2007, Mr. Terry Munson published a detailed cleanliness study using SIR benchmarks. He found that cleaning using the "dip-and-brush" process actually made the boards dirtier and more prone to premature failure. So if this is your plan, well, maybe you should re-think it.

        Most people using alcohol develop problems with white residues, especially when cleaning lead-free materials. If these residues are streaky lines across the board, your techs are not rinsing thoroughly. Have them re-clean the board. But if the residues are an even, smooth layer of white film across a large area this usually indicates you have the wrong solvent for that flux. You will need to upgrade to a stronger solvent and the problem will go away.

        Now, about worker safety. This is the third weakness of alcohol cleaners. Alcohol has a flashpoint of about 15 degrees C -- around room temperature. In the U.S., anything with a flashpoint below 55 degrtees F / 15 degrees C is considered "extremely flammable" and a significant safety hazard. Do not use these cleaners in open-topped degreasers. Do not use them in uncontrolled aerosol sprays.

        Do not use them in open trays where they might spill. Do use them with good ventilation and keep fire extinguishers available in every area where they are used. Remember, alcohol burns with an invisible flame! You can walk right into a alcohol fire and never see the flames. This makes it, in my mind, an extremely poor choice when so many other, stronger and safer options are available.



        Alconox,LiquiNox,Citranox,Citrajet,Alcojet,Luminox,Terg-A-Zyme,ALCOTABS,Detergent 8,Det-O-Jet,kyzen電子清洗劑,Aquanox A4625B,Aquanox A4651US,Ionox I3302,Lonox l5611D,LONOX L5314,HFE-7100,3M FC-40,3M FC-3283,3M FC-770,正溴丙烷(Npb)清洗劑,一氟二氯乙烷(HCFC-141B)清洗劑,助焊劑清洗劑,錫膏清洗劑,PCBA清洗劑,鋼網清洗劑,Dynasolve 218,Dynasolve CU-7,Dynasolve 165,Dynasolve 185,Dynasolve 175,Dynasolve 180

        上海昆邦化工有限公司 版權所有 2011 滬ICP備09009627號-5
        聯系人:蔣滿平 電話:021-58528856 傳真:021-58528166 手機:13917171467 電子郵件:13917171467@163.com